Help Center

Knowledgebase
PanelGrip Installation
Posted by on 15 September 2015 05:08 PM

PanelGrip Installation:
1.    Plumbing PanelGrip® Base Shoe Moulding
Before completing attachment of PanelGrip Base Shoe Moulding to substrate  – take all necessary steps to assure that the mounted Shoe is adjusted such that the inside channel of the Shoe is plumb to +/- 1/8" at an extended height of 42". Spend the time required to plumb the Shoe to this tolerance since the glass will only be as plumb as the Shoe.

2.    Clear the PanelGrip Base of All Debris.

3.    Place Isolators
Place the PanelGrip Plastic Isolators into the Base Shoe Moulding. On inclines, a dab of silicone may be used to keep them in place while placing glass. Space Plastic Isolators a maximum of 14" on center with a maximum of 4" in from the left and right edges of each panel – 4 isolators per 4 foot panel.

4.    Place Glass
Place the glass atop the Plastic Isolators in the Base Shoe Moulding.
Warning: With multi-panel Railings, do not line up the edge of a panel with the end of the Base Shoe Moulding – place the panels so that they span PanelGrip Base Shoe Moulding butt joints to assist in alignment.

5.    Insert PanelGrip
Have someone hold the panel in place while you insert the Aluminum PanelGrip mechanism into place on the opposite side of the glass in alignment with the Plastic Isolators. Make sure that the plastic pad on the PanelGrip is facing the glass.

6.    Tighten PanelGrip
Using a 3/16" hex head wrench or the PanelGrip Torque Wrench, tighten the Cap Screw on the PanelGrip mechanism. While tightening, the plastic pad will break away from the Aluminum as the unit expands.

7.    Confirm Alignment and Tighten
Confirm alignment and make adjustments prior to final tightening which will compress and lock the panel into place.

Remember, PanelGrip is self-centering and self-plumbing. Make sure you have properly plumbed the Shoe as noted in Step 1.

Once you have confirmed position, use a 3/16" hex head wrench or our PGTWRENCH to make the PanelGrip Cap Screw snug-tight, then continue tightening to 10 ft-lbf (120 in-lbf) of torque. Repeat on all other PanelGrip mechanisms to secure the panel in position. DO NOT OVERTIGHTEN.

8.    "Shake"
Grasp top of glass and pull toward you and then away from you five times. This will serve to remove any slack in the mechanism. Retighten the PanelGrip Cap Screws as noted in Step 7.

9.    Insert Spacing Pads
Repeat with other lites of glass. Insert 1/4" Spacing Pads between glass panels to prevent glass-to-glass contact. Trim as required.

10.    Seal top of shoe
Once glass is properly positioned, seal gap at the top of the PanelGrip Base Shoe Moulding using one of our two standard Gasket styles. Spray glass cleaner onto glass to facilitate insertion of gaskets.

PanelGrip is subject to one or more of the following patents: US7730682, US8181405, NZ581456, CA2697162, EP2171180 and AU2008282693.



Attachments 
 
 109.pdf (936.22 KB)
 114.pdf (557.79 KB)
(1 vote(s))
Helpful
Not helpful

Comments (0)
Post a new comment
 
 
Full Name:
Email:
Comments:
CAPTCHA Verification 
 
Please enter the text you see in the image into the textbox below (we use this to prevent automated submissions).